Intro
So where in part 1 of this evaluation I introduced the hotmirror filter, its use and the two types of filter available, I continued in part 2 with preliminary results as side-by-side samples of both types of filter next to a control image shot by a non-infrared camera.
Again I’d remind you of something I stated before: if you want to hear me say “X is better than Y” this my not be a recommended blog for you to read.
Methodology – this time
So where in part 1 I introduced some technical concepts as well as the testing methodology I had drafted, Part 2 was a deep dive into the results of a shoot pitting a regular camera body and lens against a full-spectrum converted camera with the same lens but two different filters: the in-mount clip-in filter by STC Optics and the 2nd-generation screw-in filter provided by IRreCams.de . Comparison was done at 3 focal lengths (16mm, 35mm and 85mm) and on a bright sunny day with the sun at various angles (0, 45, 90 and 180 degrees) to the sun. For the full outcome I’d refer you to the conclusions paragraph in Part 2
This time I took the full-spectrum camera with me to a Mediterranean country to see if the outcome would be different under different lighting conditions and with higher levels of UV and temperature fluctuations.
The relevant web-albums for you to check
You can see the results I got on two different days (and different elevations on a mountain) in album 1 and album 2. I leave it up to you to spot the differences. A few of the comparisons are shown below.


Why only at 16 and 35mm focal lengths? Because this particular lens is not the strongest performer at 85mm, its extreme tele-setting, which would probably even out any comparison or invalidate the results.
A few of the results on the other shooting day starting with a single evening shot – as I dd not bring a tripod, the blue-hour shot below was as close as I got to testing at night:



Final conclusions
In general, I’d like to divide my conclusions into two distinct categories, usability and “ease of use” against pure image quality. To start with the latter, image quality:
Image quality
Assessing image quality comes down to some general impressions as well as a more critical view of sharpness, color accuracy and contrast combined with any very apparent issues such as the lens flare observed with the clip-in filter in Part 1 of this blog.
Overall, the Normal Plus filter supplied to me for this test by Sven Lamprecht of IRreCams in Germany (same company that converted my camera to full spectrum) had a more consistent performance with superior sharpness and detail at focal lengths between 16 and 35mm and identical performance the the clip-in filter at longer focal lengths. But as I explained before, it may very well be due to another factor being the lens itself which slightly drops it performance below the threshold required to identify filter-introduced variables.
Literally the only “issue” if I should at all call it that is a bit of a color cast under some lighting conditions which was most noticeable in blue skies which came out slightly purplish. This was easily handled by setting a white balance based on the image itself rather than accepting the WB set by the camera at the time of shooting. As I always shoot raw (and convert with Darktable) I found this such a minor issue that I’d not hold it against the filter quality-wise.
Usability conclusions
I can say as I did after Part 2 of this evaluation that I find the Normal Plus filter as supplied by IRreCams superior to the STC clip-in filter from a purely photographic perspective. I might be elect to use the clip-in filter if my expectations are to shoot infrared images as well as simple family vacation snaps with a single (non-UWA) lens and light travel. When switching lenses, the clip-in filter can stay in the camera’s lens-mount as long as you do not angle the camera downward.
Another factor is sturdiness and ease of cleaning and again, I have to give it to the Normal Plus filter. Easy to clean with a lens cloth, sturdy screwthread and also super nice to handle. The clip-in feels as if it would snap in two if you hold it the wrong way and the filter material itself seems very thin and delicate. I’d use a blower and soft lens brush on it but certainly never a lens fluid and cloth.
One more observation which I left out last time is of course the viewfinder image. Although exposure and focus are consistent if using the optical viewfinder or OVF rather than live-view is that with the clip-in filter you are looking straight through the lens via the camera mirror which leaves the bluish hot-mirror filter out of the optical path and leaves you with a bog-standard viewfinder issue as with any unconverted DSLR. With the lens-mounted screw-in filter your OVF turns rather bluish and makes it easy to assess real colors in the shot. I strongly preferred using live-view in either scenario but for quick snapshots or under extremely bright daylight conditions, the OVF turned out a life-saver at times.
Last words on the subject (and one true IR image shot with the same camera and lens)
I have enjoyed doing this comparison tremendously and am rather surprised by its outcome to be quite honest. There is something quite technically different between placing a filter in the lensmount, behind the lens’ back element and screwing it on the front of the lens itself. I certainly recommend the Normal Plus filter when image quality is extremely important – if cost is an objection, get it for your best lens (or the largest diameter and use step-down rings). The clip-in though is an entirely valid and useful item to have and to use, turning your IR camera into a regular one with all but the most extreme wide angle lenses and under most circumstances except for those with a bright light source just outside the frame.
So, HAVE FUN!
A parting IR shot taken during the same period and the same lens

[EDIT]Additional remarks and Reddit response
After posting this blog I received an extremely interesting response from Reddit user Astrobarn who is very active in the infrared photography group on that platform.
I’m not sure I agree with the IRreCams filter being tied for second in a lot of those shots where it produces purple skies.
I wonder if the STC streak could be mitigated by blacking the edges of the glass in the clip filter, for some reason they leave them rather sharp and reflective with no black paint on the edges which would help immensely.
Perhaps you could do a more detailed sharpness test because I’m not seeing the dramatic drop in sharpness you suggested at 16mm. Is the total filter stack between the sensor and lens thicker than stock with the clip filter installed? That would definitely explain peripheral sharpness issues due to astigmatism and field curvature. If one plans to use clip filters you should have the full spectrum conversion done with the thickness of the clip filters factored in.
I’ll take an even closer look at the results but what really peaked my interest is his/her suggestion that blackening the edges of the STC might be a fix for the ugly light streak and flare I experienced when shooting wide and with the sun just outside of the top of the frame. This sounds so common sense I’m rather ashamed I did not even consider it before. Bare metal edges can- and will reflect light something fierce of course.
The other suggestion of doing a conversion with the thickness of the clip filters factored in does make sense but, and this is a big thing to me, sounds fairly limiting as that automatically means the use of lens filters is no longer optimal. If you’re committed to use clip-in filters only, it certainly is the way to go but seeing I want to keep my options open another argument for using lens filters presents itself. Those clip-in filters are hard to come by in Europe (mine came with a hefty Customs import charge on top of the already high shipping charges) so I’m not sure I’d recommend going that route unless your are based in the US. r/Astrobarn also wrote:
I think you will need blacking ink or paint, sharpie is invisible in IR and UV and only blocks about 50% of visible light.
You are correct the camera is mostly only usable with clip filters, a thinner than expected sensor stack tends to have less of a negative effect other than potentially losing infinity focus. My camera modification is designed around clip filters, with a clear filter for full spectrum, a UVIR filter for visible and then custom filters for different spectra. I use full spectrum by far the least often.
These comments are extremely valid and may certainly be useful to some readers (with similar use cases) which is why I’m adding them to my blog with the previous approval of r/astrobarn of course.


